 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 2SK3443 TOSHIBA Field Effect Transistor Silicon N Channel MOS Type (-MOSV) 2SK3443 Switching Regulator, DC-DC Converter and Motor Drive Applications * * * * Low drain-source ON resistance: RDS (ON) = 50 m (typ.) High forward transfer admittance: Yfs = 9 S (typ.) Low leakage current: IDSS = 100 A (VDS = 150 V) Enhancement mode: Vth = 3.0 to 5.0 V (VDS = 10 V, ID = 1 mA) Unit: mm Absolute Maximum Ratings (Ta = 25C) Characteristics Drain-source voltage Drain-gate voltage (RGS = 20 k) Gate-source voltage Drain current DC (Note 1) Symbol VDSS VDGR VGSS ID IDP PD EAS IAR EAR Tch Tstg Rating 150 150 30 30 120 125 468 30 12.5 150 -55 to 150 Unit V V V A W mJ A mJ C C Pulse (Note 1) Drain power dissipation (Tc = 25C) Single pulse avalanche energy (Note 2) Avalanche current Repetitive avalanche energy (Note 3) Channel temperature Storage temperature range JEDEC JEITA TOSHIBA SC-97 2-9F1B Weight: 0.74 g (typ.) Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Thermal Characteristics Characteristics Thermal resistance, channel to case Symbol Rth (ch-c) Max 1.00 Unit C/W Circuit Configuration Notice: Please use the S1 pin for gate input signal return. Make sure that the main current flows into the S2 pin. 4 Note 1: Ensure that the channel temperature does not exceed 150C. Note 2 VDD = 50 V, Tch = 25C (initial), L = 773 H, RG = 25 , IAR = 30 A Note 3: Repetitive rating: pulse width limited by maximum channel temperature This transistor is an electrostatic-sensitive device. Please handle with caution. 1 2 3 1 2009-09-29 2SK3443 Electrical Characteristics (Note 4) (Ta = 25C) Characteristics Gate leakage current Drain cut-off current Drain-source breakdown voltage Gate threshold voltage Drain-source ON resistance Forward transfer admittance Input capacitance Reverse transfer capacitance Output capacitance Rise time Turn-on time Switching time Fall time Turn-off time Total gate charge (gate-source plus gate-drain) Gate-source charge Gate-drain ("miller") charge tf toff Qg Qgs Qgd VDD 120 V, VGS = 10 V, ID = 30 A - Symbol IGSS IDSS V (BR) DSS Vth RDS (ON) Yfs Ciss Crss Coss tr ton 10 V VGS1 0V 4.7 G S1 RL = 5.0 S2 ID = 15 A VOUT D VDS = 10 V, VGS = 0 V, f = 1 MHz Test Condition VGS = 25 V, VDS = 0 V VDS = 150 V, VGS = 0 V ID = 10 mA, VGS = 0 V VDS = 10 V, ID = 1 mA VGS = 10 V, ID = 15 A VDS = 10 V, ID = 15 A Min 150 3.0 4.5 Typ. 50 9 2030 340 1200 20 40 10 40 45 21 24 Max 10 100 5.0 55 pF Unit A A V V m S VDD 75 V - ns nC Duty < 1%, tw = 10 s = Note 4: Connect the S1 and S2 pins together, and ground them except during switching time measurement. Source-Drain Diode Ratings and Characteristics (Note 5) (Ta = 25C) Characteristics Continuous drain reverse current (Note 1, Note 5) Pulse drain reverse current (Note 1, Note 5) Continuous drain reverse current (Note 1, Note 5) Pulse drain reverse current (Note 1, Note 5) Forward voltage (diode) Reverse recovery time Reverse recovery charge Symbol IDR1 IDRP1 IDR2 IDRP2 VDS2F trr Qrr Test Condition IDR1 = 30 A, VGS = 0 V IDR = 30 A, VGS = 0 V, dIDR/dt = 100 A/s Min Typ. 250 1.75 Max 30 120 1 4 -1.5 Unit A A A A V ns C Note 5: IDR1, IDRP1: Current flowing between the drain and the S2 pin. Ensure that the S1 pin is left open. IDR2, IDRP2: Current flowing between the drain and the S1 pin. Ensure that the S2 pin is left open. Unless otherwise specified, connect the S1 and S2 pins together, and ground them. Marking Note 6: A line under a Lot No. identifies the indication of product Labels. Part No. Not underlined: [[Pb]]/INCLUDES > MCV (or abbreviation code) Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]] Lot No. Note 6 K3443 Characteristics indicator Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2 2009-09-29 2SK3443 ID - VDS 50 Common source Tc = 25C Pulse test 100 15 10 9.5 Common source Tc = 25C 80 Pulse test 15 ID - VDS 12 11 40 Drain current ID (A) 9 30 8.5 20 8 7.5 VGS = 7 V 0 Drain current ID (A) 60 10 40 9 10 20 8 VGS = 7 V 0 1 2 3 4 5 0 0 4 8 12 16 20 Drain-source voltage VDS (V) Drain-source voltage VDS (V) ID - VGS 50 Common source VDS = 10 V Pulse test 5 VDS - VGS Common source Tc = 25C Pulse test 40 VDS (V) Drain-source voltage 4 Drain current ID (A) 30 25 20 100 3 2 ID = 30 A 1 15 7.5 10 Tc = -55C 0 0 4 8 12 16 20 0 0 4 8 12 16 20 Gate-source voltage VGS (V) Gate-source voltage VGS (V) Yfs - ID 100 Common source VDS = 10 V Pulse test 1 RDS (ON) - ID Common source Tc = 25C Pulse test Forward transfer admittance Yfs (S) 25 10 Tc = -55C 100 Drain-source on resistance RDS (ON) (m) 0.1 VGS = 10 V 15 1 0.01 0.1 0.1 1 10 100 0.001 1 3 5 10 30 50 100 300 500 1000 Drain current ID (A) Drain current ID (A) 3 2009-09-29 2SK3443 RDS (ON) - Tc (m) Common source 0.18 VGS = 10 V Pulse test 0.16 0.14 0.12 0.1 0.08 0.06 0.04 0.02 0 -80 -40 0 40 80 120 160 1 0 ID = 7.5 A ID = 30 A ID = 15 A 0.2 1000 Common source Tc = 25C Pulse test 100 IDR - VDS Drain-source on resistance RDS (ON) Drain reverse current IDR (A) 10 10 V 5V 3V VGS = 0 V -0.2 -0.4 -0.6 -0.8 -1.0 -1.2 -1.4 -1.6 -1.8 -2.0 Case temperature Tc (C) Drain-source voltage VDS (V) Capacitance - VDS 30000 10000 6 Vth - Tc Common source VDS = 10 V ID = 1 mA Pulse test Vth (V) Gate threshold voltage Ciss Coss Crss 3 10 30 100 300 1000 (pF) 5 5000 3000 1000 500 300 100 50 Common source 30 VGS = 0 V f = 1 MHz Tc = 25C 10 0.1 1 Capacitance C 4 3 2 1 0 -80 -40 0 40 80 120 160 Drain-source voltage VDS (V) Case temperature Tc (C) PD - Tc 200 200 Dynamic input/output characteristics 20 Common source ID = 30 A Tc = 25C Pulse test VDS VDD = 120 V 60 V 30 V VGS 40 4 Drain power dissipation PD (W) VDS (V) 160 160 16 Drain-source voltage 80 80 8 40 10 0 40 80 120 160 200 0 0 20 40 60 80 0 100 Case temperature Tc (C) Total gate charge Qg (nC) 4 2009-09-29 Gate-source voltage 120 120 12 VGS (V) 2SK3443 rth - tw 10 Normalized transient thermal impedance rth (t)/Rth (ch-c) 1 Duty = 0.5 0.2 0.1 0.1 0.05 0.02 0.01 0.01 0.00001 PDM t T Duty = t/T Rth (ch-c) = 1.0C/W 0.001 0.01 0.1 1 10 Single pulse 0.0001 Pulse width tw (S) Safe operating area 300 ID max (pulsed) * 500 EAS - Tch Avalanche energy EAS (mJ) 100 400 30 100 s * 1 ms * 300 (A) Drain current ID 10 DC operation Tc = 25C 200 100 3 0 25 1 50 75 100 125 150 Channel temperature (initial) Tch (C) * Single nonrepetitive pulse 0.3 Tc = 25C Curves must be derated linearly with increase in temperature. 15 V VDSS max 30 100 300 BVDSS IAR VDD VDS 0.1 1 3 10 -15 V Drain-source voltage VDS (V) Test circuit RG = 25 VDD = 50 V, L = 773 H Wave form AS = 1 B VDSS L I2 B 2 - VDD VDSS 5 2009-09-29 2SK3443 RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 6 2009-09-29 |
Price & Availability of 2SK344309
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |